校园网网络设计 第3页
校园网网络设计 第3页
Router(config-if)#ip address 192.168.21.1 255.255.255.0
Router(config-if)#no shutdown
%LINK-5-CHANGED: Interface FastEthernet1/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet1/0, changed state to up
Router(config-if)#
Router(config-if)#exit
Router(config)#router rip
Router(config-router)#network 192.168.20.0
Router(config-router)#network 192.168.30.0
Router(config-router)#network 192.168.21.0
Router1：
Router>enable
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#interface FastEthernet0/0
Router(config-if)#ip address 192.168.40.1 255.255.255.0
Router(config-if)#no shutdown
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
Router(config-if)#
Router(config-if)#exit
Router(config)#interface FastEthernet1/0
Router(config-if)#ip address 192.168.41.1 255.255.255.0
Router(config-if)#no shutdown
沈 阳 大 学
课程设计说明书 NO.9
%LINK-5-CHANGED: Interface FastEthernet1/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet1/0, changed state to up
Router(config-if)#
Router(config-if)#exit
Router(config)#router rip
Router(config-router)#network 192.168.40.0
Router(config-router)#network 192.168.41.0
Router(config-router)#
%LINK-5-CHANGED: Interface FastEthernet1/0, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet1/0, changed state to down
%LINK-5-CHANGED: Interface FastEthernet1/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet1/0, changed state to up
Roter2：
Router>enable
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#interface FastEthernet0/0
Router(config-if)#ip address 192.168.50.1 255.255.255.0
Router(config-if)#no shutdown
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
Router(config-if)#
Router(config-if)#exit
Router(config)#interface FastEthernet0/1
Router(config-if)#ip address 192.168.60.1 255.255.255.0
Router(config-if)#no shutdown
沈 阳 大 学
课程设计说明书 NO.10
%LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up
Router(config-if)#
Router(config-if)#exit
若图片无法显示请联系QQ3249114,本论文免费,转发请注明源于www.751com.cn
Router(config-if)#
Router(config-if)#exit
Router(config)#router rip
Router(config-router)#network 192.168.50.0
Router(config-router)#network 192.168.60.0
Router(config-router)#network 192.168.51.0
Router(config-router)#
%LINK-5-CHANGED: Interface FastEthernet1/0, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet1/0, changed state to down
%LINK-5-CHANGED: Interface FastEthernet1/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet1/0, changed state to up
Router4：
Router>enable
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#interface FastEthernet4/0