摘要PLC控制系统由主从PLC组成,采用的是“主从管理”的工作模式。固定列PLC为固定不动的货架列。固定列PLC根据各个货架上安装的传感器,触摸屏的输入信号,来确定系统运行状态,控制电机的运转实现货架移动,通过485总线向移动列发出指令,控制整个系统正确运行。本文围绕PLC控制系统的设计,主要进行以下主要工作:82783

(1)总体方案设计:利用自顶而下的设计理念,使用功能模块化设计的方法,根据所要实现的系统功能制定系统各个模块设计;

(2)硬件选型:针对本次课题的需求,完成硬件设备的最优化选型。

(3)软件设计:依据总体方案设计,选用满足系统所要实现功能的最优方案。以永宏PLC的B1系列为基础,完成系统各项软件模块设计。

(4)系统测试与评估:利用永宏WinProladder软件对系统进行仿真,对照预期的实现目标对仿真结果的性能进行评估。

毕业论文关键词  移动存储货架  永宏FATEK通讯协议  WinProladder  PLC

毕业设计说明书外文摘要

Title          The Design of PLC Control System  on the Removable Storage Shelfs           

Abstract PLC control system consists of a master PLC component and many slave PLC components, adopting a "master-slave management" mode of operation。 The master PLC is a stationary shelf row, the master PLC according to the input signal from the sensor installed on each shelf and the touch screen, determined the system status, controlled the operation of the motor to achieve shelfs movement, sent instructions via 485 bus, controlled the whole system operating correctly。 This subject focused on the design of PLC control system, mainly for the following main tasks:

(1) Overall Design: the use of top-down design, the use of functional modular design, the design of each module of the system according to the system functions to be achieved;

(2) Hardware Selection: complete the selection of optimized hardware met this subject。 

(3) Software Design: Based on the overall design, select the system to meet the optimal program functions。 With the use of the B1 series of Yong Hong PLC, to finish the software design of all modules。

(4) System Test and Evaluation: system simulation by the use of Yong Hong WinProladder software, evaluation on the performance of the simulation results compared to the expected goals。 

Keywords   removable storage shelfs   Yong Hong protocol   WinProladder   PLC

目   次

1  引言 1

1。1  研究背景及价值 1

1。2  PLC简介及优势特点 1

1。3  国内外研究现状 2

1。4  论文结构安排 2

2  PLC控制系统的总体设计 4

2。1  系统功能需求分析 4

2。2  系统设计模型介绍 5

3  PLC控制系统的硬件选型 6

3。1  系统设备选型指标分析 6

3。2  设备选型介绍 7

3。3  设备连接使用说明 9

4  PLC控制系统的软件设计 11

4。1  软件设计总体规划

上一篇:用于立体视觉的景深信息生成方法改进Matlab仿真
下一篇:Arduino基于多声呐检测的无人机避障技术研究

热环境对磁记忆信号的影响ANSYS有限元分析

连续-离散型状态观测器设...

基于Kinect手势识别的遥操...

冷库GPRS的无线数据采集系统设计

STC89C52单片机盲人用时钟的设计+电路图+程序

PLC物料自动分拣系统的设计+源程序

单相电压型逆变电路的谐...

多元化刑事简易程序构建探讨【9365字】

浅谈新形势下妇产科护理...

浅谈传统人文精神茬大學...

中国古代秘书擅权的发展和恶变

辩护律师的作证义务和保...

国内外无刷直流电动机研究现状

高校网球场馆运营管理初探【1805字】

谷度酒庄消费者回访调查问卷表

《醉青春》导演作品阐述

拉力采集上位机软件开发任务书