摘要本文针对典型一、二阶测量系统研究动态特性补偿滤波器的设计与模拟电路的实现。
根据典型一、二阶测量系统的低通特点,按巴特沃斯低通滤波器设计出补偿合成系统,然后将其传递函数除以被补偿测量系统的传递函数,从而得到补偿滤波器的传递函数。
通过单片机控制若干个双二阶有源RC电路和一阶有源RC滤波电路的级联和参数来实现补偿滤波器的传递函数。级联通过模拟开关CD4052来实现,电路的参数主要通过数字电位器x9221来调节,它们均可以由诸如AT89C51之类的通用单片机控制。20246
毕业论文中对一些具体的典型一、二阶测量系统,做出了补偿仿真(采用的Pspice)和实验测试,通过对实验结果的分析,证明了补偿滤波器的有效性。其上限截止频率通过调节可到达20kHz,并且可根据应用需求往下调节。
关键词:动态特性补偿;x9221数字电位器;CD4052;PSPICE;AT89C51。
毕业设计说明书(论文)外文摘要
Title     Design and Application of Dynamic Analog  Compensation Filters (Analog Circuit Design)                                              
Abstract
In order to improve the dynamic characteristics of dynamic measurement system, the paper research the design of dynamic compensation filters and the achievement of analog circuit for typical first-order and second-order measurement system.
This issue, according to Butterworth low-pass filter, designed synthesis compensation system, and then let it’s transfer function pide the transfer function of the measurement system, resulting in the transfer function of the compensation filter. Under the control of MCU, we can control the parameters of active filter to achieve compensation filter transfer function. Its cascade can be achieved by MCU control CD4052,  the circuit parameters can also be adjusted by the MCU to control digital potentiometer x9221.
In this paper, designed some compensation system to appropriate typical first-order and second-order measurement system. According to the analysis of the simulated and experimental results, demonstrated the effectiveness of the compensation filter. Its upper cut-off frequency can be reached by adjusting 20kHz, and can be adjusted according to the application requirements down.
Key words: Dynamic compensation; x9221 digital potentiometer; CD4052; PSPICE; AT89C51
  目次
1  绪论    1
1.1  本课题的研究背景、目的及其意义    1
1.2  本课题所涉动态补偿技术技术的国内外研究现状    2
1.3  动态特性模拟补偿滤波器的实现技术的国内外研究现状    3
1.4  本课题所研究的内容    3
1.5  论文章节安排    3
1.6  本章小结    4
2  测量系统动态特性模拟补偿传递函数设计和算法    5
2.1  补偿滤波器传递函数设计    5
2.2  补偿滤波器传递函数的具体算法    6
2.3  本章小结    7
3  动态模拟补偿滤波器的硬件电路设计    8
3.1  硬件设计总体方案    8
3.2  器件的选型    10
3.2.1  运算放大器的选择    10
3.2.2  模拟开关的选择    10
3.2.3  数字电位器的选择    11
3.2.4  单片机的选择    13
3.3  一、二阶测量系统的补偿电路及其调试电路的设计    13
上一篇:Tasco摄像仪外壳成型模具设计+CAD图纸
下一篇:ANSYS/LS-DYNA柔性网结构设计及展开过程有限元仿真研究

UG防失稳镦粗挤压大高径比...

LCD上盖注射工艺模拟分析及模具设计+CAD图纸

基于瓶颈的生产线动态平衡研究

杯形柔轮轴向变形的理论...

ANSYS爆炸载荷下船用夹层板...

NACA4412翼型气动特性数值模拟研究

AVLBOOST喷油定时对高海拔柴...

提高教育质量,构建大學生...

压疮高危人群的标准化中...

AES算法GPU协处理下分组加...

STC89C52单片机NRF24L01的无线病房呼叫系统设计

酵母菌发酵生产天然香料...

上海居民的社会参与研究

浅论职工思想政治工作茬...

基于Joomla平台的计算机学院网站设计与开发

浅谈高校行政管理人员的...

从政策角度谈黑龙江對俄...