Fig。 1。   Reference  configuration  engine  scheme。

The objective of this first part of the paper is to evaluate the different  theoretical  bottoming  cycle  configurations  applied   as a waste heat recovery system。 The amount of heat dissipated by the cooling system of an installed engine represents a heat source in a bottoming cycle。 The two-stage HDD engine used on this study

is described in the experimental setup section。 The engine is tested in order to validate a model that reproduces real working condi- tions。 This model is used to calculate the waste heat sources。 The model will be also used to perform further studies with different combinations of turbocharger and bottoming cycle system in the second part of the paper。 In the study of the engine energy, all possible residual heat sources are analyzed separately considering their potential use in the different cycle configurations。 This aspect is the main uniqueness of the work。 To consider all possible sources of engine heat involves a highly complex work due to the variety of types of these sources。 The adjustment of the heat exchange between these sources and the Rankine cycle vaporizer implies many restrictions that must be considered thus adding difficulty to the study。 However, and due to the complexity of the final solution, the analysis of how all these heat sources can be used represents a study of possible maximum energy recovering (minimum external irreversibilities), which is the objective of this paper。

Finally, two basic engine configurations with bottoming cycles are compared to analyze the global efficiency increase of the engine。

2。Experimental setup and IC engine  model

The engine studied in this article is a 12 L two-stage HDD engine [12]。 Fig。 1 shows the scheme of the engine。 The selection of a two- stage engine for this work has been done in order to keep maximum dynamic capabilities of the resulting configuration once coupled with the bottoming cycle system; transients of this engine, without a bottoming cycle, have been experimentally analyzed in [12]。

The engine model has been fitted using experimental data at full load conditions with different engine speeds。 Some of these steady points are given in Table 1。

The steady point used in the present study is 1800 rpm with full load conditions。 The main reason for this selection is that this point has the highest available residual thermal sources。 Consequently, it is considered the ideal point to assess the maximum usable energy in the engine。

The 1D gas-dynamics code used to model the engine is devel- oped at “CMT-Motores Térmicos” and called OpenWAM™   [13,14]。

Fig。  2。   Energy  scheme  reference  engine configuration。

Table 2Residual  heat sources properties。

Mass flow (kg/s) Inlet temperature (○C) Outlet temperature (○ C) Cp

(kJ/kg K) Available heat (kW)

Intercooler 0。44 127 53 1。0 35

Aftercooler 0。44 172 49 1。0 57

Exhaust gas 0。45 330

上一篇:改善重型SCR系统的应用程序英文文献和中文翻译
下一篇:齿条刀具对渐开线直齿轮根切英文文献和中文翻译

张家港某舾装码头工程设计+CAD图纸

海洋工程英文文献和中文翻译

船舶建造工程仿真英文文献和中文翻译

知识工程的汽车覆盖件冲...

计算机辅助工程设计重型...

机械工程设计选材基础知...

国际工程项目组织与管理英文文献和参考文献

压疮高危人群的标准化中...

AES算法GPU协处理下分组加...

提高教育质量,构建大學生...

酵母菌发酵生产天然香料...

STC89C52单片机NRF24L01的无线病房呼叫系统设计

基于Joomla平台的计算机学院网站设计与开发

浅谈高校行政管理人员的...

从政策角度谈黑龙江對俄...

上海居民的社会参与研究

浅论职工思想政治工作茬...